您好,歡迎光臨萊州中科聚峰有限公司網站! 主營自動攪拌車,攪拌一體車,自動上料攪拌車等各種規格的產品。
15098551508
自動上料攪拌車行業持續領跑者!
點擊撥打服務熱線:4008791999

您的位置:首頁 - 技術問答 > 常見問題 >

常見問題

大型混凝土上料攪拌車詳述水泥罐料斗的結構!

發布時間:2021-04-12 來源:http://www.pembeyol.com/ 瀏覽量:

概述:水泥罐通常作為混凝土攪拌站(樓)的配套產品使用,應用十分普遍。但是小編還是要提醒大家在購買水泥罐時,要認真檢查其料斗結構是否合理。
水泥罐通常作為混凝土攪拌站(樓)的配套產品使用,應用十分普遍。但是小編還是要提醒大家在購買水泥罐時,要認真檢查其料斗結構是否合理。因為料斗結構對水泥罐的運用性能為重要。料斗結構的合理形狀,料斗與卸料口形狀及位置的合理確定,對水泥罐防止結拱,促使造成整體流具有決定性的意義。因料斗結構的形狀和卸料口的位置與形狀,決定著物料通過料斗的能力,而物料的機械性質制約著料斗本身的結構、形狀與尺寸。
Cement tank is usually used as a supporting product of concrete mixing plant (building), and it is widely used. But Xiaobian still wants to remind you that when you buy cement tanks, you should carefully check whether the hopper structure is reasonable. Because the hopper structure is important to the performance of cement tank. The reasonable shape of hopper structure, the shape and position of hopper and discharge port are of decisive significance to prevent arching of cement tank and promote the overall flow. The shape of the hopper structure and the position and shape of the discharge port determine the ability of the material to pass through the hopper, while the mechanical properties of the material restrict the structure, shape and size of the hopper itself.
           自動攪拌車廠家
混凝土攪拌車料斗的卸料口位置通常有中心卸料、邊角和側邊卸料,后二者由于存在不對稱性,成拱的可能性小,但在相同的傾角下要求料斗的高度大一些。料斗的倒錐通常是從圓形到圓形,方形到方形,圓形到矩形,或矩形到圓形,倒錐下口的形狀,常受配料器入口形狀的制約,使兩者配合起來,便于卸料而不結拱。
The position of discharge port of concrete mixer hopper usually includes center discharge, corner discharge and side discharge. The latter two are not likely to form arch due to asymmetry, but the height of hopper is required to be larger under the same inclination angle. The inverted cone of hopper is usually from round to round, from square to square, from round to rectangular, or from rectangular to round. The shape of the lower opening of the inverted cone is often restricted by the shape of the inlet of the batcher, so that the two can be combined to facilitate discharging without arching.
為了獲得暢通的整體流動,避免結拱,水泥罐有各種形式的料斗可供選擇。對稱料斗的對稱兩邊的物料向中間擠壓,易阻塞結拱,但容易制作;相對于非對稱料斗,其長度較小,多用于流動性好的物料,非對稱料斗與前者的情況相反,不易結拱,故采用較多.但同樣傾角,其料斗長度比對稱者要長。
In order to obtain smooth overall flow and avoid arching, various types of hoppers are available for cement tank. The material on both sides of the symmetrical hopper is squeezed to the middle, which is easy to block and arch, but it is easy to make. Compared with the asymmetric hopper, its length is smaller, and it is mostly used for materials with good fluidity. The asymmetric hopper is opposite to the former, which is not easy to arch, so it is used more. But with the same inclination angle, its hopper length is longer than that of the symmetric hopper.
技術支持:濟南諾商  XML   TXT   
本網站部分資源來自互聯網,如有侵權,請聯系我們及時刪除
分享按鈕

截屏,微信識別二維碼

微信號:

點擊微信號復制,添加好友

 打開微信

日本阿v不卡高清在线播放_2019久久久高清456_被公每天都侵犯的我正在播放