您好,歡迎光臨萊州中科聚峰有限公司網站! 主營自動攪拌車,攪拌一體車,自動上料攪拌車等各種規格的產品。
15098551508
自動上料攪拌車行業持續領跑者!
點擊撥打服務熱線:4008791999

您的位置:首頁 - 技術問答 > 公司新聞 >

公司新聞

防止自動攪拌車上料時堵料和粘料的方法?

發布時間:2020-08-10 來源:http://www.pembeyol.com/ 瀏覽量:

概述:1、上下料時間參數不合理:自動上料機因料倉內無法加裝料位機,所以行業基本都有時間控制。如何設置時間參數,上下料時間設置其實很簡單,
1、上下料時間參數不合理:自動上料機因料倉內無法加裝料位機,所以行業基本都有時間控制。如何設置時間參數,上下料時間設置其實很簡單,在初次使用時,先設置一個小的時候,然后根據每次吸料位置慢慢加,當達到料位達到吸料口的時間,再減去一秒就是合理時間。放料時間是確保放完料再加一秒。這樣做有兩個好處:一是料位太高對濾芯傷害特別大,二是每次料都能放干凈。
1. Unreasonable loading and unloading time parameters: automatic feeding machine can not be installed in the silo, so the industry basically has time control. How to set the time parameter? The setting of loading and unloading time is very simple. In the first use, set a small time first, and then add slowly according to the suction position. When the material reaches the material level and reaches the suction port, subtracting one second is the reasonable time. The discharging time is to ensure that one second is added after discharging. This has two advantages: one is that the material level is too high to damage the filter element; the other is that the material can be put clean every time.
2、自動上料攪拌車進料口給料量是否合理:正確的方式是物料在吸料口和空氣形成一定的氣物混合比,在氣流的推動下均勻流入上料機。這個時候我們需要將料槍設計帶有補氣功能。如果物料積壓時間過長可能很硬,這個時候需要在料槍上裝一個振蕩器,敲碎結塊的物料。
2. Whether the feeding amount at the feeding port of the automatic feeding mixer is reasonable: the correct way is to form a certain air-material mixing ratio between the material at the suction port and the air, and evenly flow into the feeding machine under the driving of the air flow. At this time, we need to design the material gun with air replenishment function. If the material overstocking time is too long, it may be very hard. At this time, we need to install an oscillator on the material gun to break the agglomerated materials.
           自動攪拌車
防止自動攪拌車上料粘罐的方法:
Methods to prevent the automatic mixer from sticking to the tank:
1、隨車帶上減水劑:減水劑是一種在維持混凝土坍落度不變的條件下,能減少拌合用水量的混凝土外加劑,隨車攜帶,能對混凝土進行很好的調節。
1. Water reducer with vehicle: water reducer is a kind of concrete admixture which can reduce the water consumption of mixing under the condition of maintaining the concrete slump unchanged. It can adjust the concrete well when carried with the vehicle.
2、回廠檢查罐內水量:每次出車任務完成回到站內的時候,檢查儲水罐內的水量,讓水罐中的水隨時處于滿罐的狀態,以備不時之需。
2. Return to the factory to check the water volume in the tank: when returning to the station after the completion of the vehicle dispatching task, check the water volume in the water storage tank to make the water in the water tank full at any time in case of emergency.
3、離廠前檢查混凝土質量:可能會因為原料的不同,每一盤混凝土質量都會有變化。
3. Check the concrete quality before leaving the factory: the quality of each concrete plate may change due to different raw materials.
4、減少車輛行駛時間:混凝土運距一般在直徑30千米范圍以內,出車之前規劃好路線以及車輛通行情況。
4. Reduce the driving time of vehicles: the concrete transportation distance is generally within the range of 30 km in diameter, and the route and vehicle traffic condition shall be planned before the vehicle is driven.
5、減少損失先卸料:如果遇到人為因素或者不可抗因素,導致長時間無法卸料的情況,一旦發現混凝土開始凝結,在報備負責人之后立刻進行卸料,以防整個罐體報廢。
5. Unloading first to reduce losses: in case of long-term failure to discharge due to human factors or irresistible factors, once the concrete starts to set, the unloading shall be carried out immediately after reporting to the person in charge, so as to prevent the whole tank body from being scrapped.
以上是小編整理的關于自動攪拌車上料時防止堵料和粘罐的相關方法,希望對大家有所幫助,想要了解更多內容歡迎點擊我們的http://www.pembeyol.com網站。
The above is about the automatic mixer truck loading to prevent blocking and stick to the relevant methods, hope to help you, want to learn more, welcome to click our http://www.pembeyol.com Website.
技術支持:濟南諾商  XML   TXT   
本網站部分資源來自互聯網,如有侵權,請聯系我們及時刪除
分享按鈕

截屏,微信識別二維碼

微信號:

點擊微信號復制,添加好友

 打開微信

日本阿v不卡高清在线播放_2019久久久高清456_被公每天都侵犯的我正在播放